Accessories lifts
Elevate your workshop lifts to the next level with Ravaglioli’s premium accessories. From control boxes to adaptors and kits, our selection of accessories lifts will enhance your lifting operations.
Showing 1–99 of 300 results
Door protections for 2-post lifts
1 set / 2 pieces
Energy kit for S50/S42
Compressed air connection under the track, 230 V socket at the control panel | 1 piece
Equipment to move lift
Equipment to move lift
Extensions for rear platforms | 280 mm
For 4-post lifts | 1 pair
Factory assembly of the lighting kit S440A5 on the lift
Floor leveling for vertical scissor lifts with 6 m platform length – G
Galvanized
Floor leveling for vertical scissor lifts with 8 m platform length
Floor leveling for vertical scissor lifts with 9 m platform length
Front wheel stops for RAV4800 Series
For loading the new “maxi” VW van with double rear axle | Retrofit kit | 1 pair
Front wheel stops S4800A6 | as replacement for original wheel stops
For loading the new “maxi” VW van with double rear axle
LED lighting kit
Lighting kit for all lifts
for all lifts
Limit switch | operated by bar | for 1-phase power supply | supplied not installed
For all lifts with 1-phase power supply
Long front ramps
Long front ramps
Long front ramps 1200 mm
Long front ramps 1200 mm
Manual pump for emergency descent
Mounting set
For 305 series | fitted in factory instead of standard pads
Pad adapter V-shaped | 1 set / 4 pieces
Capacity 3200 kg, height adjustable 150 – 190 mm, incl. threaded end Ø 45 mm
Pad adapter V-shaped | 1 set / 4 pieces
Capacity 5500 kg, height adjustable 150 – 190 mm, incl. threaded end Ø 60 mm
Pads 120 mm, ≤ 3.2 t | for M30 arms | 1 set / 4 pieces
For turntables with M 30 threaded end (except for K and R arms)
Pads 2.7 – 3.2 t | 1 set / 4 pieces
For lifts with capacity 2.7 – 3.2 t
Pads 2.7 – 3.2 t | 1 set / 4 pieces
For lifts with capacity 2.7 – 3.2 t
Pads 2.7 – 3.2 t | 1 set / 4 pieces | fitted in factory
For lifts with capacity 2.7 – 3.2 t | Set of pads S336A1, mounted instead of standard pads (5.337 series)
Pads 2.7 – 3.2 t | 1 set / 4 pieces | fitted in factory
For lifts with capacity 2.7 – 3.2 t | Set of pads S336A1, mounted instead of standard pads
Pads 2.7 – 3.2 t | 1 set / 4 pieces | fitted in factory
For lifts with capacity 2.7 – 3.2 t | Set of pads S336A1, mounted instead of standard pads
Pads 2.7 – 3.2 t | 1 set / 4 pieces | fitted in factory
For lifts with capacity 2.7 – 3.2 t | Set of pads S305A14, mounted instead of standard pads
Pads 200 mm, ≤ 3.2 t | for M30 arms | 1 set / 4 pieces
For turntables with M 30 threaded end (except for K and R arms)
Pads 80 mm, ≤ 3.2 t | for M30 arms | 1 set / 4 pieces
For turntables with M 30 threaded end (except for K and R arms)
Retaining belts kit
Retrofit kit Arms with rotating final stage
1 set / 4 pieces
Retrofit kit Parking position switch rolling jack
For scissor lift S38/S50
Run-up ramps
2600 mm | 1 pair
Run-up ramps
Long, 2600 mm | ramps S442A3 replacing the standard ramps | 1 pair
Run-up ramps
Long, 1500 mm | ramps S4352SIA3 replacing the standard ramps | 1 pair
Run-up ramps
Long, 1500 mm | ramps S4406LA4 replacing the standard ramps | 1 pair
Run-up ramps
Long, 1200 mm | ramps S4800A2 replacing the standard ramps | 1 pair
Run-up ramps
Long, 1100 mm | ramps S4351A2 replacing the standard ramps | 1 pair
Run-up ramps
Long, 1000 mm | ramps S4405LA2 replacing the standard ramps | 1 pair
Run-up ramps
Long, 1000 mm | ramps S4300A2 replacing the standard ramps | 1 pair
Run-up ramps
Long, 1900 mm | ramps S4505LA2 replacing the standard ramps | 1 pair
Run-up ramps
Long, 1640 mm | 1 pair
Run-up ramps
Long | ramps S4655LA2 replacing the standard ramps | 1 pair
Run-up ramps
Long, 2600 mm | ramps S440A3 replacing the standard ramps | 1 pair
Run-up ramps
Long | ramps S4652LA3 replacing the standard ramps | 1 pair
Run-up ramps
Long, 1200 mm | ramps S4651LA3 replacing the standard ramps | 1 pair
Run-up ramps
Long, 1500 mm | ramps S4502LSIA2 replacing the standard ramps | 1 pair
Run-up ramps
Front | ramps S6350A2 supplied instead of standard front stops | 1 pair
Run-up ramps
Long, 1600 mm | ramps S6350A4 replacing the standard ramps | 1 pair
Run-up ramps
3300 mm | for all surface installation versions | 1 pair
Spacers 200 mm, bushing Ø 60 mm | 1 set / 4 pieces
200 mm, bushing Ø 60 mm | 1 set / 4 pieces
Spacers for wheel alignment versions of series 6352
To close turntable housing | 1 set / 6 pieces
Spacers for wheel alignment versions of series 6352
To total close turntable housing | 1 set / 10 pieces
Special pads increased, 90 mm | for M30 thread arms | 1 set / 4 pieces
For vehicles with internal lifting points (for example for: Renault Espace and Talisman)
Special pads increased, 90 mm | for M30 thread arms | 1 set / 4 pieces | Supplied in place of the standard pads
For vehicles with internal lifting points (for example for: Renault Espace and Talisman)
Support pads for Mercedes Sprinter/VW LT + Crafter | Ø 45 mm
V-shaped supports | bushing Ø 45 mm | 1 set / 2 pieces
Support pads for Mercedes Sprinter/VW LT + Crafter | Ø 60 mm
Holding set, adjustable – 2 x rod-shaped supports, 2 x V-shaped supports | bushing Ø 60 mm | needed spacers S370A7-A8-A15 | 1 set / 4 pieces
Support plates for floors with a concrete thickness of 150 mm (+20 mm)
Plates to install baseless 2-post lifts on floor with poor capacity | Min. requirement: R’bk 200 withrnthickness 150 mm | 1 set / 2 pieces
Support set for wheel free
Supporting arm extensions
90 mm, capacity reduced to 2.7 t | 1 set / 2 piec
Supporting arm extensions
90 mm, capacity reduced to 2.7 t | 1 set / 2 pieces
Supporting arm extensions
100 mm, capacity reduced to 2.7 t | 1 set / 2 pieces
Supporting arm extensions
Capacity reduced to 3.5 t | 1 set / 2 pieces
Supporting bars
For frame installation / lift + frame installation into the foundation
Supports for chassis lifting | adjustable | bushing Ø 60 mm | 1 set / 4 pieces
Needed spacers S370A7-A8-A15
Warning light
Light signal “system in use”
Traverses for XS30-CAT
For vans and off-road vehicles | 1 set / 2 pieces
Seat for turntables | plates and slip plates excluded | 1 set
For RAV4350, RAV4401, RAV4405L, RAV4501L, RAV4651L, RAV4800
Support trestle
7500 kg, 1330 – 2030 mm | Grey (RAL 7040)
Support trestle
10000 kg, 1235 – 2040 mm | Grey (RAL 7040)
Support trestle
10000 kg, 1235 – 2040 mm | with on springs retracting rollers
LED lighting kit
Vehicle fuses
For turntable, Ø 120 mm | 1 set / 2 pieces
Drive-through ramps 1350 mm, ground ramps
Additional ramps to drive-through the lift, for 600N series lifts with wheel-free jack | 1 set / 2 pieces
Drive-through ramps 1560 mm, suspended ramps
Additional ramps to drive-through the lift, for 600N series lifts with wheel-free jack | 1 set / 2 pieces
Drive-through ramps 1800 mm, suspended ramps
Additional ramps to drive-through the lift, for 600N series lifts with wheel-free jack | 1 set / 2 pieces
Drive-through ramps 2000 mm, suspended ramps
Additional ramps to drive-through the lift, for 600N series lifts with wheel-free jack | 1 set / 2 pieces
Wheel fork reduction for tires Ø 700 – 500 mm
Wheel fork reduction for tires Ø 800 – 700 mm
1 piece
Wheel fork reduction for tires Ø 900 – 800 mm
1 piece
Forklift brackets
For moving lifting units of electrohydraulic mobile column lifts
Pads
Support plate, rubber pad, adjustable – for quick-positioning on 4 heights | 4-stage | 1 set / 4 pieces
Support plates
3.5 t | allows installation on floors with poor capacity or lower concrete thickness | 1 set / 2 pieces
Warning light
Light signal “system in use”
Wheel clamp mount
Adjustable special version, wheel Ø 500 – 1200 mm
Extension for MRG55
100 mm (3000/4000/5500 kg) / 150 mm (7000/8500/10000 kg)
Drive-through ramps 1350 mm, ground ramps
Additional ramps to drive-through the lift, for 600N series lifts without wheel-free jack | 1 set / 2 pieces
Drive-through ramps 1560 mm, suspended ramps
Additional ramps to drive-through the lift, for 600N series lifts without wheel-free jack | 1 set / 2 pieces
Drive-through ramps 1800 mm, suspended ramps
Additional ramps to drive-through the lift, for 600N series lifts without wheel-free jack | 1 set / 2 pieces
Drive-through ramps 2000 mm, suspended ramps
Additional ramps to drive-through the lift, for 600N series lifts without wheel-free jack | 1 set / 2 pieces
Control unit installation kit
2 m, control unit right | mounting the operating unit in a special position – in drive-up direction “right” from the platform, at a distance of 2 m | suitable for RAV.640N1.193278, RAV.640N2.193117, RAV.640N1.193391, RAV.650N1.193742, RAV.650N2.193858, RAV.650N2.193520, RAV.650N2.193667, RAV.660N2.193360 and RAV.650N2.193384
Control unit installation kit
2 m, control unit left | mounting the operating unit in a special position – in drive-up direction “left” from the platform, at a distance of 2 m
Wheel-lifting platform kit
Hose cover 1 m | for surface installation
1 m | for surface installation
Limit switch | operated by bar | for 3-phase power supply | supplied not installed
For all lifts with 3-phase power supply
Run-up ramps
Long additional ramps for low ground clearance vehicles
Wheel free cross-beam for MRG55
15 t